|
- 品牌：德國KAYSEN
- 貨號：KS5893569
- 發布日期： 2019-10-11
- 更新日期： 2025-09-23
| 外型尺寸 | |
| 貨號 | KS5893569 |
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制藥、石油、冶金、染料、冶煉、電力、電鍍、農藥、造紙、食品、紡織等行業酸洗工藝、制酸制堿、噴漆工藝、有色金屬冶煉中的電解液輸送、離子膜項目中的氯水輸送、廢水處理、電鍍、農藥領域。 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 電動 |
| 適用介質 | 水 |
離心油泵-油泵-KAYSEN泵業
GERMANY KAYSEN PUMP CO .,LTD
離心油泵的主要過流部件有吸水室、葉輪和壓水室。通過改變泵過流部件材質、密封形式和增加冷卻系統用于輸送熱水、油類、腐蝕性或含磨粒的介質。
主要特點：
●葉輪是離心泵的核心部分，它轉速高輸出力大，葉輪上的葉片又起到主要作用，葉輪在裝配前要通過靜平衡實驗。葉輪上的內外表面要求光滑，以減少水流的摩擦損失。
●泵體也稱泵殼，它是水泵的主體。起到支撐固定作用，并與安裝軸承的托架相連接。
●泵軸的作用是借聯軸器和電動機相連接，將電動機的轉距傳給葉輪，所以它是傳遞機械能的主要部件。
●軸承是套在泵軸上支撐泵軸的構件，有滾動軸承和滑動軸承兩種。滾動軸承使用牛油作為潤滑劑加油要適當一般為2/3～3/4的體積太多會發熱，太少又有響聲并發熱！滑動軸承離心泵結構使用的是透明油作潤滑劑的，加油到油位線。太多油要沿泵軸滲出并且漂*，太少軸承又要過熱燒壞造成事故！在水泵運行過程中軸承的溫度*在85度一般運行在60度左右，如果高了就要查找原因（是否有雜質，油質是否發黑，是否進水）并及時處理！
●密封環又稱減漏環。葉輪與泵殼間的間隙過大會造成泵內高壓區的水經此間隙流向低壓區，影響泵的出水量，效率降低！間隙過小會造成葉輪與泵殼摩擦產生磨損。為了增加回流阻力減少內漏，延緩葉輪和泵殼的所使用壽命，在泵殼內緣和葉輪外援結合處裝有密封環，密封的間隙保持在0.25～1.10mm之間為宜。
●填料函主要由填料，水封環，填料筒，填料壓蓋，水封管組成。填料函的作用主要是為了封閉泵殼與泵軸之間的空隙，不讓泵內的水流不流到外面來也不讓外面的空氣進入到泵內。始終保持水泵內的真空！當泵軸與填料摩擦產生熱量就要靠水封管住水到水封圈內使填料冷卻。保持水泵的正常運行。所以在水泵的運行巡回檢查過程中對填料函的檢查是特別要注意！在運行600個小時左右就要對填料進行更換。
主要優點：
●水力模型先進，效率高，性能范圍廣
●泵運行平穩，噪音低
●軸為全封結構，確保了不與介質接觸，不銹蝕，使用壽命長
●軸封采用軟填料密封或機械密封，密封安全可靠、結構簡單，維修方便快捷
主要應用：
●工業
●油管道
●輪船
●遠距離供油
●碼頭配套
The main flow components of the centrifugal oil pump include a suction chamber, an impeller and a pressurized water chamber. By changing the material of the pump's flow-through components, the form of the seal, and adding a cooling system for transporting hot water, oil, corrosive or abrasive-containing media.
main feature:
●The impeller is the core part of the centrifugal pump. It has high output speed and large output force. The blade on the impeller plays a major role. The impeller should pass the static balance test before assembly. The inner and outer surfaces of the impeller are required to be smooth to reduce the frictional loss of water flow.
● The pump body is also called the pump casing, which is the main body of the pump. It acts as a support and is attached to the bracket on which the bearing is mounted.
● The function of the pump shaft is to connect the coupling to the motor and transmit the torque of the motor to the impeller, so it is the main component that transmits mechanical energy.
●The bearing is a member that supports the pump shaft on the pump shaft, and has two kinds of rolling bearings and sliding bearings. Rolling bearings use butter as a lubricant to refuel properly. Generally 2/3 ~ 3 / 4 of the volume will be too much heat, too little and there is noise and fever! The sliding bearing centrifugal pump structure uses a transparent oil as a lubricant and is refueled to the oil level line. Too much oil will ooze along the pump shaft and float *, too few bearings will overheat and burn out! During the operation of the pump, the temperature of the bearing is at most 85 degrees and generally runs at about 60 degrees. If it is high, it is necessary to find the cause (whether there are impurities, whether the oil is black or not, whether it is water) and deal with it in time!
● The sealing ring is also called the leak reducing ring. The gap between the impeller inlet and the pump casing is too large, so that the water in the high pressure zone of the pump flows to the low pressure zone through the gap, which affects the water output of the pump and reduces the efficiency! Too small a gap will cause friction between the impeller and the pump casing. In order to increase the backflow resistance and reduce the internal leakage, and delay the service life of the impeller and the pump casing, a sealing ring is arranged at the inner edge of the pump casing and the outer joint of the impeller, and the sealing gap is preferably maintained between 0.25 and 1.10 mm.
●The stuffing box is mainly composed of packing, water sealing ring, packing tube, packing gland and water sealing tube. The function of the stuffing box is mainly to close the gap between the pump casing and the pump shaft, so that the water in the pump does not flow to the outside and the outside air does not enter the pump. Always keep the vacuum inside the pump! When the pump shaft and the packing friction generate heat, the water seals the water to the water seal ring to cool the packing. Keep the pump running properly. Therefore, it is especially important to check the stuffing box during the running inspection of the pump! The packing should be replaced after about 600 hours of operation.
The main advantage:
●Advanced hydraulic model, high efficiency and wide performance range
●The pump runs smoothly and the noise is low.
●The shaft is a full-sealed structure, ensuring no contact with the medium, no corrosion, long service life
●The shaft seal is sealed with soft packing or mechanical seal. The seal is safe and reliable, the structure is simple, and the maintenance is convenient and quick.
main application:
●Industry
● oil pipeline
●ship
●Long distance oil supply
●Wharf support
Cutting submersible sewage pump
Diving flow booster
Submersible mixed flow pump
Submersible return pump
Corrosion resistant sewage pump
Submersible mixer
位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
