|
- 品牌：德國KAYSEN
- 貨號：KS8305679
- 發布日期： 2019-10-12
- 更新日期： 2024-11-21
| 外型尺寸 | |
| 貨號 | KS8305679 |
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制藥、石油、冶金、染料、冶煉、電力、電鍍、農藥、造紙、食品、紡織等行業酸洗工藝、制酸制堿、噴漆工藝、有色金屬冶煉中的電解液輸送、離子膜項目中的氯水輸送、廢水處理、電鍍、農藥領域。 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 電動 |
| 適用介質 | 水 |
電動插桶泵-插桶泵-KAYSEN泵業
GERMANY KAYSEN PUMP CO .,LTD
電動插桶泵應根據工藝流程，給排水要求，從液體輸送量、裝置揚程、液體性質、管路布置以及操作運轉條件五個方面加以考慮。保養方便、性能可靠、使用壽命長、外觀簡潔、結構先進合理、國際標準、輸送不含固體顆粒液體。油桶泵分類：手搖油桶泵，電動油桶泵，氣動油桶泵。
主要特點：
手提式電動插桶泵（油桶泵）操作條件：
桶泵可以輸送各類液體，由于液體多樣性，選型必須考慮到液體和泵管材質及密封圈材質的相容性，如需不同泵管材質及密封圈材質，化學介質反應性能狀況，請致電我們公司技術部詳細咨詢。
電動油桶泵不是所有的產品都使用于輸送食品，藥品等有衛生要求的場合，如需要使用，使用者需要確認不會危害相關食品，藥品的品質；輸送食品、藥品等有衛生要求的場合時可選用PTFE-SS管道，清洗方便，使用前必須做好清洗工作。
粘度：
輸送有粘度液體時候，桶泵的輸送流量和揚程都會有所下降，超過額定輸送粘度，電機有過載的危險，嚴重時會損壞電機。
主要應用：
該系列電動油桶泵可輸送酸、堿、鹽、油品、飲料等介質，廣泛用于化工、石油化工、精細化工、染料化工、環保、水處理、醫藥、食品等部門。同時適用于中小型油田、油庫、加油站、農機站、企事業單位、車隊、車輛船舶等輸送汽油、煤油、柴油、輕質燃油的理想工具。如在易燃易爆場合使用。
電動插桶泵的使用與維護：
1、全新或長期擱置不用的電動抽液泵，開箱后用500伏兆歐表測量所有帶電零件與可能觸及的金屬零件之間絕緣電阻，在接近工作溫度時應不低于7兆歐。
2、使用前，須檢查各接線柱是否牢固，接地線必須可靠牢固。
3、檢查電源電壓是否與額定電壓相符，不能超過或低于額定電壓10%的電源上使用。
4、使用本泵時，切勿有損電線，避免水、油進入電機、開關、電器部位。
5、禁止在含有易燃和腐蝕性氣體條件下工作，以保證安全生產及各電氣原件的正常工作。
6、使用中如發現有異常雜音時，應立即停機，檢查原因，直至設法排除后方可繼續使用。
7、本泵不宜空運轉，使用時吸液完畢立即停泵，因本泵電機空載速可達10000轉/分立左右，否則將會磨壞，萬向節葉輪，嚴重時會損壞泵管。
8、調換電刷：電刷磨損到不能使用時應立即調換，否則會損壞換向器，嚴重會燒壞電機。
9、電動抽液泵應定期檢查，不般至少三個月檢查一次，經常使用的應每月檢修一次，檢修時應該全部拆開，消除內部積塵、油污。如果換向器上積碳過多可用酒精擦洗換向器表面。如有損壞零件，應調換相同零件。
10、不用時請放置在干燥、清潔沒有腐蝕性氣體的環境中。
Electric drum pump
Pneumatic slurry pump
The oil drum pump should be considered according to the process flow, water supply and drainage requirements, from the five aspects of liquid delivery, device head, liquid properties, piping layout and operating conditions. It is easy to maintain, reliable in performance, long in service life, simple in appearance, advanced in structure and reasonable, international standard, and transports solid liquid without liquid. Oil drum pump classification: hand oil drum pump, electric oil drum pump, pneumatic oil drum pump.
main feature:
Portable electric drum pump (oil drum pump) operating conditions:
The barrel pump can transport all kinds of liquids. Due to the diversity of liquids, the selection must take into account the compatibility of the liquid and pump tube materials and the material of the sealing ring. If different pump tube materials and sealing ring materials are needed, the chemical medium reaction performance status, please Call our company's technical department for detailed consultation.
Electric drum pump Not all products are used to transport food, medicines and other places where there are hygienic requirements. If needed, users need to confirm that they will not harm the quality of related foods and medicines; PTFE-SS pipe can be used for cleaning, and cleaning must be done before use.
Viscosity:
When the viscosity liquid is delivered, the delivery flow rate and head of the barrel pump will decrease, exceeding the rated delivery viscosity, and the motor may be overloaded. In severe cases, the motor may be damaged.
main application:
This series of electric oil drum pumps can transport acid, alkali, salt, oil, beverage and other media, widely used in chemical, petrochemical, fine chemical, dye chemical, environmental protection, water treatment, medicine, food and other departments. At the same time, it is suitable for medium and small oil fields, oil depots, gas stations, agricultural machinery stations, enterprises and institutions, fleets, vehicles and ships, etc. It is an ideal tool for conveying gasoline, kerosene, diesel and light fuel oil. For use in flammable and explosive places.
Use and maintenance of the oil drum pump:
1. New or long-term unused electric pump. After opening the box, measure the insulation resistance between all live parts and metal parts that may be touched with a 500 volt megger. It should be no less than 7 megohms when approaching the working temperature.
2. Before use, check that the terminals are secure and the grounding wire must be reliable and secure.
3. Check if the power supply voltage matches the rated voltage and should not be used on a power supply that is 10% or lower than the rated voltage.
4. When using this pump, do not damage the wires and prevent water and oil from entering the motor, switch and electrical parts.
5. It is forbidden to work under conditions of flammable and corrosive gases to ensure safe production and normal operation of various electrical components.
6. If abnormal noise is found during use, stop immediately and check the cause until you can try to eliminate it.
7. The pump should not be operated empty. When the liquid is used, the pump will stop immediately. Because the pump motor has a no-load speed of 10,000 rpm, it will be worn out, and the universal joint impeller will damage the pump tube in severe cases.
8. Change the brush: When the brush is worn and cannot be used, it should be replaced immediately. Otherwise, the commutator will be damaged and the motor will be burnt out.
9. The electric pump should be inspected regularly. It should be inspected at least once every three months. It should be inspected once a month for regular use. It should be dismantled during maintenance to eliminate internal dust and oil. If there is too much carbon on the commutator, the commutator surface can be scrubbed with alcohol. If there are damaged parts, the same parts should be replaced.
10. When not in use, please place it in an environment that is dry and clean without corrosive gases.
位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
