進口齒輪油泵（進口油泵品牌）

德國KAYSEN凱森進口齒輪油泵概述
本系列齒輪泵主要有齒輪、軸、泵體、安全閥、軸端密封所組成。齒輪油泵適用于輸送不含固體顆粒和纖維，無腐蝕性，溫度不高于80℃，粘度為5×10-6～1.5×10-3m2/s (5-00cSt)的潤滑油或性質類似潤滑油的其他液體。

主要特點：

1、齒輪油泵使用規定電壓

線路電壓不超過抽液泵銘牌上所規定電壓的±10%方可使用。

2、齒輪油泵*裝備

開箱后按結構示意圖裝配，接上電動機

（1）并緊接連電機

（2）使之泵體與電機為一體

（3）上接好出水輪管

3、齒輪油泵使用前檢查各部件外型完好才能開機使用。

4、齒輪油泵不宜作空運轉，使用時，抽吸完畢，即停泵，否則會加速葉輪密封件軸承等磨損。也可能磨損泵管，因本泵電機空載轉速可達10000轉/分。

5、齒輪油泵及時調換電刷，電刷磨損到將不能使用時，須及時調換（2只電刷同時調換）否則會使電刷與換向器接觸不良引起壞損，損壞換向器，嚴重時會燒壞電樞。

6、齒輪油泵在下列情況下不得使用，在使用過程中如發現絕緣損壞，電源線工電纜護套破裂，插頭插座開裂或接觸不良，以及斷續運轉，出現嚴懲火花等故障時，電機外殼操作時，應立即進行修理。在未修復前不得使用。

7、齒輪油泵防止過載，使用時，凡遇轉速異常或降低時，應即停機檢查是否有雜物卡住葉輪或電機是否發生故障，抽液泵因故剎車時必須立即切斷電源

8、齒輪油泵使用工具要愛惜，所有抽涂泵要小心輕放避免受到?jīng)_擊。

Germany  Kaysen imported gear oil pump overview

This series of gear pumps mainly consists of gears, shafts, pump bodies, safety valves and shaft end seals. Gear oil pump is suitable for conveying lubricating oil without solid particles and fibers, non-corrosive, temperature not higher than 80 ° C, viscosity of 5×10-6～1.5×10-3m2/s (5-00cSt) or similar lubrication Other liquids of oil.

main feature:

1, the gear oil pump uses the specified voltage

The line voltage shall not exceed ±10% of the voltage specified on the pumping pump nameplate.

2. How to equip the gear pump

After unpacking, assemble according to the structural diagram and connect the motor

(1) and immediately connected to the motor

(2) Make the pump body and the motor integrated

(3) Connect the water wheel tube

3. Before using the gear oil pump, check that the parts are in good condition before starting to use.

4. The gear oil pump should not be operated at idle. When using, the pumping is completed, that is, the pump is stopped, otherwise the bearing of the impeller seal will be accelerated. It is also possible to wear the pump tube because the pump motor has a no-load speed of 10,000 rpm.

5. The gear oil pump will change the brush in time. When the brush is worn and will not be used, it must be replaced in time (2 brushes are exchanged at the same time). Otherwise, the brush and the commutator may cause bad damage and damage the commutator. The armature will be burned out.

6. The gear oil pump should not be used under the following conditions. If the insulation damage is found during the use, the power cable sheath is broken, the plug and socket are cracked or the contact is bad, and the operation is intermittent, and the motor casing is operated when there is a serious punishment for sparks. Repairs should be made immediately. Do not use until unrepaired.

7. The gear oil pump prevents overload. When it is used, when the speed is abnormal or reduced, it should be stopped to check if there is any debris stuck in the impeller or the motor is faulty. If the pump is braked, the power must be cut off immediately.

8, gear oil pump use tools to be cherished, all pumping pumps should be handled with care to avoid impact.

泵服務Pumps service

我們的服務團隊提供從單一來源 - 安裝，調試，維護，維修，咨詢，升級，培訓，備件和優化泵的所有工作。Our service team offers everything from a single source - Installation, commissioning, maintenance, repair, consulting, upgrades, training, spare parts and optimization of pumps.

一切從單一來源 我們長期的經驗是您在現場調試，售后維護，維修，泵現代化和優化方面的優勢。我們向您保證*的個人支持。 我們的服務團隊為其他制造商的產品提供及時，專業和可靠的幫助。預訂我們的服務套餐，您可以長期保證系統的*運行可靠性。我們會與您一起進行 評估，從而創建透明度并根據您的需求制定*解決方案。在檢查您的工廠后，我們確定其節約潛力并通過提高安裝的泵的效率來實現它。另外，這個單獨的解決方案降低了您的維護成本。您不必考慮人員，也不必考慮維護計劃或?qū)嵱贸绦?。大會按照既定的時間表進行，并在我們訓練有素的人員的協助下進行。

Everything from a single source Our long-standing experience is your advantage in commissioning on site, after-sales maintenance, repair, modernization and optimization of pumps. We guarantee you the best personal support. Our service team provides prompt, professional, and reliable assistance – also for other manufacturers’ products. Book our service package and you can be sure of the best operating reliability for your systems in the long term. We conduct an expert assessment together with you, thus creating transparency and making an optimum solution possible that is tailored to your needs. After examining your plant, we determine its savings potential and realize it by improving the efficiency of the pumps installed. Additionally, this individual solution lowers your maintenance costs. You do not have to think about personnel, nor about maintenance schedules or utilities. Assembly is conducted according to defined schedules and with assistance from our trained personnel.

我們的服務概述 · 供應原裝備件 · 部署經過培訓的人員 · 安裝和啟動 · 檢查 · 維修，檢修，維修 · 對早期故障檢測進行機器評估 · 咨詢和現代化 · 性能和振動測量 · 故障和損壞分析 · 可行性研究 · 泵和系統的能源咨詢 · 制定維護計劃 · 服務和維護協議 · 自動化和電力系統 · 電子設備 · 訓練

An overview of our services · Supply of original spare parts · Deployment of trained personnel · Installation and start-up · Inspection · Repairs, overhauls, maintenance · Machine assessment by an expert for early fault detection · Consulting and modernization · Performance and vibration measurement · Fault and damage analyses · Feasibility studies · Energy consulting for pumps and systems · Preparation of maintenance schedules · Service and maintenance agreements · Automation and Electrical Power Systems · Electronic equipment · Training

進口齒輪油泵（進口油泵品牌）