3344免费高清看片_日韩欧洲在线精品一区_高潮爽死抽搐白浆gif视频_久久久成人毛片无码国产_91高端极品外围在线观看二区_国产老肥婆牲交_日日碰狠狠添天天爽不卡_天堂无码三级综合avav_免费A级毛片AV无码_亚洲网络精品在线观看

進口不銹鋼磁力泵(進口磁力泵）

德國KAYSEN凱森進口不銹鋼磁力泵概述

進口不銹鋼磁力泵是由磁力泵由泵、磁力傳動器、電動機三部分組成。關鍵部件磁力傳動器由外磁轉子、內磁轉子及不導磁的隔離套組成。 當電動機帶動外磁轉子旋轉時，磁場能穿透空氣隙和非磁性物質，帶動與葉輪相連的內磁轉子作同步旋轉，實現動力的無接觸傳遞，將動密封轉化為靜密封。由于泵軸、內磁轉子被泵體、隔離套完全封閉，從而 解決了“跑、冒、滴、漏”問題，消除了煉油化工行業易燃、易爆、有毒、有害介質通過泵密封泄漏的安全隱患，有力地保證了職工的身心健康和安全生產。

將n對磁體(n為偶數)按規律排列組裝在磁力傳動器的內、外磁轉子上，使磁體部分相互組成完整藕合的磁力系統。當內、外兩磁極處于異極相對，即兩個磁極間的位移角Φ=0，此時磁系統的磁能*；當磁極轉動到同極相對，即兩個磁極間的位移角Φ=2π/n，此時磁系統的磁能*。去掉外力后，由于磁系統的磁極相互排斥，磁力將使磁體恢復到磁能*的狀態。于是磁體產生運動，帶動磁轉子旋轉。

主要特點：

永磁體

由稀土永磁材料制成的永磁體工作溫度范圍廣(-45－400℃)，矯頑力高，磁場方向具有很好的各向異性，在同極相接近時也不會發生退磁現象，是一種很好的磁場源。

隔離套

在采用金屬隔離套時，隔離套處于一個正弦交變的磁場中，在垂直于磁力線方向的截面上感應出渦電流并轉化成熱量。渦流的表達式為：其中Pe－渦流；K—常數；n—泵的額定轉速；T－磁傳動力矩；F－隔套內的壓力；D－隔套內徑； 一材料的電阻率； —材料的抗拉強度。當泵設計好后，n、T是工況給定的，要降低渦流只能從F、D等方面考慮。選用高電阻率、高強度的非金屬材料制作隔離套，在降低渦流方面效果十分明顯。

冷卻潤滑液流量

泵運轉時，必須用少量的液體對內磁轉子與隔離套之間的環隙區域和滑動軸承的摩擦副進行沖洗冷卻。冷卻液的流量通常為泵設計流量的2%-3%，內磁轉子與隔離套之間的環隙區域由于渦流而產生高熱量。當冷卻潤滑液不夠或沖洗孔不暢、堵塞時，將導致介質溫度高于永磁體的工作溫度，使內磁轉子逐步失去磁性，使磁力傳動器失效。當介質為水或水基液時，可使環隙區域的溫升維持在3-5℃；當介質為烴或油時，可使環隙區域的溫升維持在5-8℃。

滑動軸承

磁力泵滑動軸承的材料有浸漬石墨、填充聚四氟乙烯、工程陶瓷等。由于工程陶瓷具有很好的耐熱、耐腐蝕、耐摩擦性能，所以磁力泵的滑動軸承多采用工程陶瓷制作。由于工程陶瓷很脆且膨脹系數小，所以軸承間隙不得過小，以免發生抱軸事故。

由于磁力泵的滑動軸承以所輸送的介質進行潤滑，所以應根據不同的介質及使用工況，選用不同的材質制作軸承。

Germany Kaysen imported stainless steel magnetic pump overview

The stainless steel magnetic pump is composed of a magnetic pump consisting of a pump, a magnetic actuator and a motor. The key component magnetic actuator consists of an outer magnetic rotor, an inner magnetic rotor and a non-magnetic magnetic isolation sleeve. When the motor drives the outer magnetic rotor to rotate, the magnetic field can penetrate the air gap and the non-magnetic material, and the inner magnetic rotor connected with the impeller rotates synchronously to realize the non-contact transmission of the power, and the dynamic seal is converted into a static seal. Since the pump shaft and the inner magnetic rotor are completely closed by the pump body and the isolation sleeve, the problem of “running, escaping, dripping and leaking” is completely solved, and the flammable, explosive, toxic and harmful medium of the refining and chemical industry is eliminated from the pump seal leakage. The safety hazard has effectively guaranteed the physical and mental health and safe production of employees.

The n pairs of magnets (n is an even number) are regularly arranged and assembled on the inner and outer magnetic rotors of the magnetic actuator, so that the magnet portions form a complete coupled magnetic system. When the inner and outer magnetic poles are in opposite poles, that is, the displacement angle Φ=0 between the two magnetic poles, the magnetic energy of the magnetic system is the lowest; when the magnetic pole rotates to the same pole, the displacement angle between the two magnetic poles is Φ=2π. /n, at this time the magnetic energy of the magnetic system is the largest. After the external force is removed, the magnetic force will return the magnet to the state with the lowest magnetic energy because the magnetic poles of the magnetic system repel each other. The magnet then moves to drive the magnetic rotor to rotate.

main feature:

Permanent magnets

The permanent magnet made of rare earth permanent magnet material has a wide operating temperature range (-45-400 ° C), high coercive force, good anisotropy in the direction of the magnetic field, and no demagnetization when the same pole phase is close. It is a good source of magnetic field.

Isolation set

When a metal isolating sleeve is used, the spacer is in a sinusoidal alternating magnetic field, and an eddy current is induced and converted into heat in a section perpendicular to the direction of the magnetic line. The expression of the eddy current is: where Pe- eddy current; K-constant; n - rated speed of the pump; T-magnetic drive torque; pressure in the F-sleeve; D- spacer inner diameter; resistivity of a material; Tensile strength. When the pump is designed, n and T are given by the working conditions. To reduce the eddy current, only F, D and so on can be considered. The use of high-resistivity, high-strength non-metallic materials to make the isolation sleeve, the effect is very obvious in reducing the eddy current.

Cooling lubricant flow

When the pump is running, a small amount of liquid must be used to flush and cool the annulus region between the inner magnetic rotor and the spacer sleeve and the friction pair of the sliding bearing. The flow rate of the coolant is usually 2% to 3% of the pump design flow rate, and the annulus region between the inner magnetic rotor and the isolation sleeve generates high heat due to the eddy current. When the cooling lubricating fluid is not enough or the flushing hole is not smooth or blocked, the medium temperature is higher than the working temperature of the permanent magnet, so that the inner magnetic rotor gradually loses magnetism and the magnetic actuator fails. When the medium is water or water-based liquid, the temperature rise of the annulus region can be maintained at 3-5 ° C; when the medium is hydrocarbon or oil, the temperature rise of the annulus region can be maintained at 5-8 ° C.

Sliding bearing

The material of the magnetic pump sliding bearing is impregnated graphite, filled with polytetrafluoroethylene, engineering ceramics, and the like. Because engineering ceramics have good heat resistance, corrosion resistance and friction resistance, the sliding bearings of magnetic pumps are mostly made of engineering ceramics. Since the engineering ceramics are very brittle and the expansion coefficient is small, the bearing clearance must not be too small to avoid the occurrence of a shaft hazard.

Since the sliding bearing of the magnetic pump is lubricated by the medium to be conveyed, the bearing should be made of different materials according to different media and working conditions.

位于Schw?bischGmünd的凱森Kaysen泵業有限公司是*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持 各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現 全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。

The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.

進口不銹鋼磁力泵(進口磁力泵）